[2018 Version] Free Download N10-006 exam question With New Practice Test Software

CompTIA Network+ N10-006 Certification exam is also known as CompTIA Network+ exam. With the updated N10-006 exam questions and answers, TestsLeader has assembled to take you through 461 Q&As to prepare you for your N10-006 Exam. In the N10-006 exam dumps, you will cover all the essentials of CompTIA Network+ N10-006 exam, which will make you successful in N10-006 CompTIA Certification Exam.

♥♥ 2018 NEW RECOMMEND N10-006 Exam Questions ♥♥

N10-006 exam questions, N10-006 PDF dumps; N10-006 exam dumps:: https://www.dumpsschool.com/N10-006-exam-dumps.html (461 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate CompTIA N10-006 Dumps Exam Questions and Answers:

Version: 15.0
Question: 21

A network technician is performing a tracert command to troubleshoot a website-related issue. The following output is received for each hop in the tracert:
1 * * * Request timed out.
2 * * * Request timed out.
3 * * * Request timed out.
The technician would like to see the results of the tracert command. Which of the following will allow the technician to perform tracert on external sites but not allow outsiders to discover information from inside the network?

A. Enable split horizon to allow internal tracert commands to pass through the firewall
B. Enable IGMP messages out and block IGMP messages into the network
C. Configure the firewall to allow echo reply in and echo request out of the network
D. Install a backdoor to access the router to allow tracert messages to pass through

Answer: C

Explanation:
Tracert makes use of ICMP echo packets to trace the route between two hosts. For the command to be successful, the firewall has to allow incoming echo replies and outgoing echo requests.

Question: 22

A network technician has received comments from several users that cannot reach a particular website. Which of the following commands would provide the BEST information about the path taken across the network to this website?

A. ping
B. netstat
C. telnet
D. tracert

Answer: D

Explanation:
The tracert command is used to determine the amount of hops a packet takes to reach a destination. It makesuse of ICMP echo packets to report information at every step in the journey. This is how the path taken across the network is obtained.

Question: 23

Which of the following network devices use ACLs to prevent unauthorized access into company systems?

A. IDS
B. Firewall
C. Content filter
D. Load balancer

Answer: B

Explanation:
A firewall is a system designed to prevent unauthorized access to or from a private network. Firewalls arefrequently used to prevent unauthorized Internet users from accessing privatenetworks connected to the Internet, especially intranets. Firewalls use ACLs (access control lists) to determine which traffic is allowed through the firewall. All traffic entering or leaving the intranet passes through the firewall, which examines each message and blocks or allows the message depending on rules specified in the ACL. The rules in the ACL specify which combinations of source IP address, destination address in IP port numbers are allowed.

Question: 24

Which of the following is used to define how much bandwidth can be used by various protocols on the network?

A. Traffic shaping
B. High availability
C. Load balancing
D. Fault tolerance

Answer: A

Explanation:
If a network connection becomes saturated to the point where there is a significant level of contention, network latency can rise substantially.
Traffic shaping is used to control the bandwidth used by network traffic. In a corporate environment, business-related traffic may be given priority over other traffic. Traffic can be prioritized based on the ports used by the application sending the traffic. Delayed traffic is stored in a buffer until the higher priority traffic has been sent.

Question: 25

Which of the following is used to authenticate remote workers who connect from offsite? (Select TWO).

A. OSPF
B. VTP trunking
C. Virtual PBX
D. RADIUS
E. 802.1x

Answer: D,E

Explanation:
D: A RADIUS (Remote Authentication Dial-in User Service)server is a server with a database of user accounts and passwords used as a central authentication database for users requiring network access. RADIUS servers are commonly used by ISP’s to authenticate their customer’s Internet connections.
Remote users connect to one or more Remote Access Servers. The remote access servers then forward the authentication requests to the central RADIUS server.
E: 802.1X is an IEEE Standard for Port-based Network Access Control (PNAC). It provides an authentication mechanism to devices wishing to attach to a network.
802.1X authentication involves three parties: a supplicant, an authenticator, and an authentication server. The supplicant is a client that wishes to attach to the network. The authenticator is a network device,such as an Ethernet switch, wireless access point or in this case, a remote access server and the authentication server is the RADIUS server.

Question: 26

Which of the following provides accounting, authorization, and authentication via a centralized privileged database, as well as, challenge/response and password encryption?

A. Multifactor authentication
B. ISAKMP
C. TACACS+
D. Network access control

Answer: C

New Updated N10-006 Exam Questions N10-006 PDF dumps N10-006 practice exam dumps: https://www.dumpsschool.com/N10-006-exam-dumps.html

         

Facebook Comments